Professional, High Efficiency and Intelligent OTR Test System
Technical Specifications
| Specifications | Film Test | Package Test
(customization available) |
| Test Range | 0.01~6500 cm3/m2·d (standard)
0.07~65,000 cm3/m2·d (optional) | 0.0001~60 cm3/pkg·d |
| Number of Specimens | 1~3 with independent test results |
| Resolution | 0.001 cm3/m2·d | 0.00001 cm3/pkg·d |
| Temperature Range | 15°C~55°C (standard) |
| Temperature Accuracy | ±0.1°C (standard) |
| Humidity Range | 0%RH, 35%RH~90%RH |
| Humidity Accuracy | ±1%RH |
| Test Gas | Oxygen and air (outside of supply scope) |
| Specimen Thickness | ≤3 mm (customization is available for other thickness) | / |
| Test Area | 50 cm2 | / |
| Specimen Size | 108 mm x 108 mm | One package with temperature control device: specimen should be smaller than Ф150 mm and lower than 380 mm |
Three packages with temperature control device: specimens should be smaller than Ф100 mm, and lower than 380 mm |
No size limitation for tests without temperature control device |
| Carrier Gas | 99.999% high purity nitrogen or nitrogen with 2% hydrogen
(outside of supply scope) |
| Carrier Gas Pressure | ≥ 0.28 MPa |
| Port Size | 1/8 inch copper tubing |
| Instrument Dimension | 690 mm (L) x 350 mm (W) x 360 mm (H) |
| Power Supply | 220VAC 50Hz / 120VAC 60Hz |
| Net Weight | 70 kg |
Principle
The pre-conditioned specimen is mounted between the upper and lower chambers at ambient atmospheric pressure. One chamber contains oxygen or air and the other chamber is slowly purged by a stream of nitrogen. Due to the concentration difference between the two chambers, oxygen molecules permeate through the specimen into the nitrogen side and are taken to the coulometric sensor where proportional electrical signals are generated. The oxygen transmission rate is then obtained by analyzing and calculating the signals. For package samples, high purity nitrogen flows inside the package, and oxygen or air flows outside.
Standards
This test instrument conforms to the following standards:
ISO 15105-2, ASTM D3985, ASTM F2622, ASTM F1307, ASTM F1927, GB/T 19789, JIS K7126-2, YBB00082003
This instrument is applicable to the determination of oxygen transmission rate of:
| Basic Applications | Films
Including plastic films, plastic composite films, paper-plastic composite films, coextruded films, aluminized films, aluminum foil, aluminum foil composite films and many others |
|---|
Sheeting
Including various sorts of engineering plastics, rubber and building materials, e.g. PP, PVC and PVDC |
Packages
Including plastic, rubber, paper, paper-plastic composite, glass and metal packages, e.g. Coke bottles, peanut oil packages, Tetra Pak materials, vacuum bags, metal three-piece cans, plastic packages for cosmetic, soft tubes for toothpaste, jelly and yogurt cups |
| Extended Applications | Package Caps
Test seal performance of different package caps |
|---|
Solar Back-Sheets
Including solar back-sheets |
Plastic Pipes
Including various sorts of pipes, e.g. PPR |
Blister Packs
Test oxygen transmission rate of the whole blister packs |
Fuel Tanks of Cars
Plastic fuel tanks are widely used in cars for its light weight, buffering vibration and easy molding characters. But its fuel permeability is the most essential factor, this instrument can be used to test permeability of plastic fuel tanks |
Battery Plastic Shell
Battery electrolyte is protected by the plastic shell from outside environment. Battery service life is directly dependent on its oxygen permeability. This instrument can be used to test oxygen transmission rate of battery plastic shell |
Red Wine Bottles
Test oxygen transmission rate of red wine bottles |
Professional
This instrument can be used to measure oxygen transmission rate of film and package specimens. It has three test modes and is applicable to various materials with high, medium and low oxygen permeability. It is also embedded with high precision oxygen sensor, which provides a wide test range of 0.01~65000cm3/m2·d and durable service life.
Wide range and high precision of temperature and humidity control, adding humidity to two sides of the specimen, to support various combinations of non-standard test conditionsWorld leading pressure compensation technology ensures accurate and repeatable test resultsStandard, proportional and continuous testing modes facilitate to minimize errors caused by human factors during test processEquipped with catalyst deaerator to purify carrier gas and reduce system errors2 types of carrier gases are available: High purity nitrogen gas or hydrogen-mixed nitrogen gasConvenient fast-access calibration port for temperature and humidityReference film for accurate calibrationHigh Efficiency
OX2/230 system is based on the equal pressure method and adopts Labthink’s latest exclusive patent design of three diffusion cells integrated in one instrument for individual or multiple tests, which improves test efficiency by 3 times. It can be easily connected with 9 satellite bases together to accomplish up to 30 tests at the same time.
3 diffusion cells are integrated in one instrument with lower space occupancy rate and higher test efficiency3 distinct or equivalent specimens can be tested individually with independent test results at one operationThe system can be easily connected with a maximum of 10 instruments to accomplish up to 30 tests at the same timeOxygen transmission rate and water vapor transmission rate can be obtained at one operation by working with Labthink’s water vapor transmission rate test system together under the control of one computerIntelligent
The instrument utilizes Labthink’s latest operating software with user-friendly operating interface and intelligent data management. It also supports LystemTM Lab Data Sharing System, which ensures uniform management of test results and test reports.
Based on the user-friendly Windows operating interface for easy operationSaves test data in different formats for convenient data transferIntelligent historical data searching, comparison, analysis and printing functionsSupports LystemTM Lab Data Sharing System for uniform management of test results and test reports
- Standard Configurations
- Instrument, Professional Software, Communication Cable, Vacuum Grease, Diamond Sample Template and Valve Sets
- Optional Parts
- Satellite Base, Accessories for Package Test, Temperature Control Device, Reference Film, Sample Cutter and Vacuum Grease
- Note
- 1. The gas supply port of the instrument is 1/8 inch copper tubing;
2. Customers will need to prepare for gas supply.
